Vaddio Wall Mount and Pole Mount User Manual download pdf (Page 1)

Camera and Electronic Products for Integrators

Specifications and pricing subject to change. Vaddio and DomeVIEW are registered trademarks of Vaddio. Document 341-446, Page 1 of 2

Installation and User Guide

Curved Wall Mount and Pole Mount Kit

For DomeVIEW™ Indoor and Outdoor Pendant Mount Domes

Wall Mount Kit 998-9300-000

Wall Mount with Pole Mount Kit 998-9300-001

Installation (Curved Wall Mount 998-9300-000 Only)

1. Carefully unpack box, inspect contents for damage and verify that all components are included.

2. Attach the mount to the wall, using the appropriate fasteners (not included) for the mounting surface.

3. Route power and video leads through mount by pulling enough length to reach into the housing.

4. Attach the dome 1-½” NPT fitting to the wall mount and lock into place with the provided 1-½” NPT lock nut.

5. Refer to the housing instruction sheet to complete the installation (see Figure 1).

Installation (Curved Wall Mount and Pole Mount Kit - 998-9300-001)

1. Carefully unpack box, inspect contents for damage and verify that all components are included.

2. Feed the stainless bands through the slots and attach the mount to the pole firmly by tightening the bands with a

screwdriver (see Figure 2).

3. Install the Curved Wall Mount by attaching the wall mount to the Pole Mount with the bolts provided. Make sure

that the mount is level and tighten all four (4) bolts firmly. Run the cabling, pulling enough length through to

reach into the housing without strain.

4. Seal the wire passage with silicone sealant (not included). Provide a drip loop if the cable entry is from the top.

5. Attach the dome 1-½” NPT fitting to the wall mount and lock into place with the provided 1-½” NPT lock nut.

6. Refer to the housing instruction sheet to complete the installation.

Figure 1:

Curved Wall Mount for Indoor and Outdoor Pendant Domes

Vaddio Part # 998-9300-000

Curved Wall Mount comes with:

One (1) Curved Wall Mount

(No other screws or accessories are included)

Dimensions:

Mounting Plate (H x W) - 7.5” (19.05cm) x 4.5” (11.43cm)

Distance from Wall - 10.5” (26.67cm) to center of pipe

Height - 9.5” (24.13cm)

Figure 2:

Curved Wall Mount and Pole

Mount Adapter for Indoor and

Outdoor Pendant Domes

Vaddio Part # 998-9300-001

Pole Mount Kit comes with:

One (1) Pole Mount Adapter Plate

Four (4) Stainless Steel Bolts

Two (2) Steel bands with clamps

Dimensions:

Mounting Plate (H x W) – 7.5”

(19.05cm) x 5.25” (13.34cm)

Back Flange - 2” (5.08cm) Deep

1 2

Wall Mount Kit 998-9300-000 1

Summary of Contents

Page 1 - Wall Mount Kit 998-9300-000

Page 2

Vaddio, 4800 Quebec Avenue North, Minneapolis, MN 55428 (763)-537-3601, www.vaddio.com, Document 341-446, Page 2 of 2 SAVE THESE INSTRUCTIONS: The

Comments to this Manuals

No comments

Vaddio Wall Mount and Pole Mount User Manual Page 1

Browse online or download User Manual for Audio Vaddio Wall Mount and Pole Mount. Vaddio Wall Mount and Pole Mount User Manual

Summary of Contents

Comments to this Manuals

Vaddio Wall Mount and Pole Mount User Manual Page 1

Browse online or download User Manual for Audio Vaddio Wall Mount and Pole Mount. Vaddio Wall Mount and Pole Mount User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Audio Vaddio Wall Mount and Pole Mount