Vaddio Sony BRC-H700 User Manual Page 12

  • Download
  • Add to my manuals
  • Print
  • Page
    / 26
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 11
12
BRC-H700 Command List (4/5)
Command Set Command Command Packet Comments
Pan-tiltDrive Up 8x 01 06 01 VV WW 03 01 FF PanSpeed VV (= 01:Slow to 18h:Fast)
Down 8x 01 06 01 VV WW 03 02 FF TiltSpeed WW (= 01:Slow to 18h:Fast)
Left 8x 01 06 01 VV WW 01 03 FF
Right 8x 01 06 01 VV WW 02 03 FF
UpLeft 8x 01 06 01 VV WW 01 01 FF
UpRight 8x 01 06 01 VV WW 02 01 FF
DownLeft 8x 01 06 01 VV WW 01 02 FF
DownRight 8x 01 06 01 VV WW 02 02 FF
Stop 8x 01 06 01 VV WW 03 03 FF
AbsolutePosition 8x 01 06 02 VV 00 0Y 0Y Speed VV (= 01:Slow to 18h:Fast)
0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYYY: Pan Position*
ZZZZ: Tilt Position*
RelativePosition 8x 01 06 03 VV 00 0Y 0Y Speed VV (= 01:Slow to 18h:Fast)
0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYYY: Pan Position*
ZZZZ: Tilt Position*
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
Pan-tiltLimitSet LimitSet 8x 01 06 07 00 0W 0Y 0Y W: 1 UpRight 0:DownLeft*
0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYYY: PanLimit Position*
0x00000 (Center)
0x08A58 (Left End)
0xF75A8 (Right End)
ZZZZ: TiltLimit Position*
0x00000 (Center)
0x493D (Up End)
0xE796 (Down End)
LimitClear 8x 01 06 07 01 0W W: 1 UpRight 0:DownLeft
07 0F 0F 0F 0F 07 0F 0F 0F FF
RAMP_CURVE MODE1 8x 01 06 31 01 FF
MODE2 8x 01 06 31 02 FF
MODE3 8x 01 06 31 03 FF
D-SUB 15Pin OUTPUT Output 1 RGB 8x 01 7E 01 03 00 00 FF
Output 1 YPbPr 8x 01 7E 01 03 00 01 FF
RGB SYNC OFF 8x 01 7E 01 07 00 00 FF
RGB SYNC RGB 8x 01 7E 01 07 00 02 FF
D-SUB 15Pin SYNC 3-STATE 8x 01 7E 01 1A 00 00 FF
VD 8x 01 7E 01 1A 00 01 FF
EXT_SYNC Standard 8x 01 7E 01 2C 00 FF
Synchronous mode HD1 8x 01 7E 01 2C 01 FF
SD1 8x 01 7E 01 2C 02 FF
CAM_ImgFlip On 8x 01 04 66 02 FF
Off 8x 01 04 66 03 FF
CAM_PanReverse On 8x 01 7E 01 06 00 01 FF
Off 8x 01 7E 01 06 00 00 FF
Cam_TiltReverse On 8x 01 7E 01 09 00 01 FF
Off 8x 01 7E 01 09 00 00 FF
Cmd_Tally On 8x 01 7E 01 0A 00 02 FF When Power is on, return to off.
Off 8x 01 7E 01 0A 00 03 FF
Cmd_PT_M_Speed Preset PT Speed 8x 01 7E 01 0B 0p qq FF p: Memory number (=0 to Fh ) qq: Speed (=1 to 18h:fast)
* See the section under VISCA Command Setting Values.
Page view 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 25 26

Comments to this Manuals

No comments